new wheels/swingarm
11-02-2009 | 12:05 PM
#31
Senior Member
SuperBike
Joined: Dec 2005
Posts: 1,689
From: South Lake Tahoe, CA, USA
Very nice!
The only light wheels I have ridden were on my RC51, but it is such a completely different bike, that it's hard to tell how much of it was wheels. I just recall very light, intuitive steering. Hadn't really gotten going with it yet, though.
The bike is looking good. I hadn't seen pictures of a full Ti Mori exhaust in a while. I love the blue color that they turn.
Weren't those my rearsets way back when?
Yup. those are VTR brake calipers. I recommend swapping to the RC51 calipers.
The only light wheels I have ridden were on my RC51, but it is such a completely different bike, that it's hard to tell how much of it was wheels. I just recall very light, intuitive steering. Hadn't really gotten going with it yet, though.
The bike is looking good. I hadn't seen pictures of a full Ti Mori exhaust in a while. I love the blue color that they turn.
Weren't those my rearsets way back when?
Yup. those are VTR brake calipers. I recommend swapping to the RC51 calipers.
11-02-2009 | 12:12 PM
#32
Out of my mind, back in 5
MotoGP
Joined: Nov 2006
Posts: 6,109
From: Skurup, Sweden
Sweet!
Now get your *** in gear and go sign up for the VTROM...
Last chanche...
BTW did you remove the bellypan permanently, or is it just left of during that picture?
Now get your *** in gear and go sign up for the VTROM...
Last chanche...BTW did you remove the bellypan permanently, or is it just left of during that picture?
Last edited by Tweety; 11-02-2009 at 12:14 PM.
11-02-2009 | 07:21 PM
#34
Thread Starter
Senior Member
SuperBike
Joined: Jul 2005
Posts: 1,548
From: MN
just entered it, Tweety. I removed the bellypan for the work on the rear end of the bike.
And I have to say I thought I liked the bellypan - but now that its off, I think I actually prefer it without it - so I'm leaving it off!
And I have to say I thought I liked the bellypan - but now that its off, I think I actually prefer it without it - so I'm leaving it off!
11-03-2009 | 01:00 PM
#39
Out of my mind, back in 5
MotoGP
Joined: Nov 2006
Posts: 6,109
From: Skurup, Sweden
I can't decide which is best... But it's either on or fully off... Not putting ther stock one back... Dammit... Now I'm having modding idea's on another guys bike... This is getting serious... I need to tear mine down...
11-03-2009 | 01:12 PM
#40
Senior Member
MotoGP
Joined: Apr 2005
Posts: 5,631
From: Montreal
11-03-2009 | 01:19 PM
#41
Out of my mind, back in 5
MotoGP
Joined: Nov 2006
Posts: 6,109
From: Skurup, Sweden
Oh don't worry... I have a few parts lying around that needs to go into my spare engine...
And there needs to be added a few braces to the frame... And... Well, if you figure out where this is going, lemme know... Cuz I haven't the faintest...
I have a few parts lying around that needs to go into my spare engine...And there needs to be added a few braces to the frame... And... Well, if you figure out where this is going, lemme know...
Cuz I haven't the faintest...
11-03-2009 | 03:38 PM
#42
Thread Starter
Senior Member
SuperBike
Joined: Jul 2005
Posts: 1,548
From: MN
made me wonder. here is how it looks with and without pan.
I don't think the angles work with the swingarm very well - and would likely need trimming though its not as close as it looks in the pics.
let me know what you think
I don't think the angles work with the swingarm very well - and would likely need trimming though its not as close as it looks in the pics.
let me know what you think
11-03-2009 | 06:25 PM
#46
Thread Starter
Senior Member
SuperBike
Joined: Jul 2005
Posts: 1,548
From: MN
I think you guys are right and believe me, finding that mori lower was not easy. But with it off I am surprised that I actually prefer it too - and for sure with the lower braced swingarm. go figure.
Wicky:
go right to the source: http://web.tiscalinet.it/mario_nava/vtr1000_e.html
Wicky:
go right to the source: http://web.tiscalinet.it/mario_nava/vtr1000_e.html
11-05-2009 | 04:27 AM
#47
Senior Member
SuperSport
Joined: Dec 2005
Posts: 963
From: Sunshine Coast, Australia
Looks good Bill. Good to see you got those wheels sorted. Easier than I did!
You and I have the same headers. I have not seen another set the same (although there must be lots about the world). I chose to ceramic coat mine though. They sure are light compared to stainless pipes.
You and I have the same headers. I have not seen another set the same (although there must be lots about the world). I chose to ceramic coat mine though. They sure are light compared to stainless pipes.
Last edited by shayne; 11-05-2009 at 04:29 AM.
11-05-2009 | 07:17 PM
#49
OCMD honorary member
Superstock
Joined: May 2007
Posts: 252
From: Olympia, WA
thanks guys. mikstr they are the stock RC51 calipers, not SH. I was unsure on top or bottom bracing - its trivial but I figured the lower the weight the better and it was what JMC also suggested as having the least fit issues so.........
VTS - those look almost the same width as mine (mine are 30") and I figure I can trim at least an inch from each side - which should be close to what I want. Narrower is better. Do you know just straight across from end to end what they measure?
VTS - those look almost the same width as mine (mine are 30") and I figure I can trim at least an inch from each side - which should be close to what I want. Narrower is better. Do you know just straight across from end to end what they measure?
Again your bike looks great, not much I would change. Don't go sell'n it. I don't know what you would replace it with?
11-05-2009 | 07:35 PM
#50
Thread Starter
Senior Member
SuperBike
Joined: Jul 2005
Posts: 1,548
From: MN
couldn't sell it now VTS. to much blood sweat tears into it.
Shayne that is such a great looking bike you built - and attention to every detail!! I agree, the pipe is amazing - I think the entire system including both cans was around 9 pounds or something close.
Shayne that is such a great looking bike you built - and attention to every detail!! I agree, the pipe is amazing - I think the entire system including both cans was around 9 pounds or something close.
11-09-2009 | 10:15 PM
#51
OCMD honorary member
Superstock
Joined: May 2007
Posts: 252
From: Olympia, WA
11-09-2009 | 10:50 PM
#52
evil man of nothing
MotoGP
Joined: Jan 2006
Posts: 4,493
From: Boynton Beach, FL
I love the brakes. I just finally put my cbr calipers on the same brackets tonight. Did you also get those brackets from Glenn? What did you use for brake lines? I have convertibar clip ons so mine are lower of course, but I'm still curious. With the radial calipers one of my lines is a little too short.
11-10-2009 | 07:32 PM
#53
Thread Starter
Senior Member
SuperBike
Joined: Jul 2005
Posts: 1,548
From: MN
I love the brakes. I just finally put my cbr calipers on the same brackets tonight. Did you also get those brackets from Glenn? What did you use for brake lines? I have convertibar clip ons so mine are lower of course, but I'm still curious. With the radial calipers one of my lines is a little too short.
12-02-2009 | 08:22 PM
#54
evil man of nothing
MotoGP
Joined: Jan 2006
Posts: 4,493
From: Boynton Beach, FL
Yeah he really is. He always has (had?) the best RC51 stuff for sale on ebay. I think he told me he's selling that business off. I couldn't help myself awhile back and bought a ti sato kickstand (sorry I had to have it ) from him. He told me if I didn't like it or it didn't work to send it back and he'd refund me, no worries. Really cool guy.
So yeah I'm gonna have to bite the bullet and just order some new lines...I hate paying retail for anything but I'm probably going to have to here. I have a brembo radial mc and am just using the two separate lines. I used what I believe are the stock clips that bolt to the lower triple and it helps route the lines nice and clean. I measure and re-measured several times so I hope I get the length right. Plus I can sell my stock length galfers and make up some of the difference. I'm on more on a budget than I used to be lol.
) from him. He told me if I didn't like it or it didn't work to send it back and he'd refund me, no worries. Really cool guy.So yeah I'm gonna have to bite the bullet and just order some new lines...I hate paying retail for anything but I'm probably going to have to here. I have a brembo radial mc and am just using the two separate lines. I used what I believe are the stock clips that bolt to the lower triple and it helps route the lines nice and clean. I measure and re-measured several times so I hope I get the length right. Plus I can sell my stock length galfers and make up some of the difference. I'm on more on a budget than I used to be lol.
Thread
Thread Starter
Forum
Replies
Last Post
ziptie_1000
Classifieds
25
03-09-2009 03:44 PM
